11 min read
What Is a Remap? A Chiptuning Glossary for Tuners and Dealers
Ask three tuners what a slave file is and you may get three answers. This glossary explains the words you meet when you order tuning files, from ori and tuning file to master, slave, checksum, DTC and map, in short plain definitions grouped by where each term turns up on a real job.
What is a remap, and what do ori, slave and checksum mean? Ask three tuners what a slave file is and you may get three slightly different answers. Add mod file and DTC off, and a first order from a file service can read like another language.
This glossary puts the vocabulary in one place. The entries are short and plain, grouped by where each term turns up on a real job, with a link to the longer article when a term deserves one. It is written for garages, mobile tuners and dealers who order tuning files. Where a term means something specific on TheTuningGroup, such as what one credit buys, the entry says so. Where the meaning varies by tool vendor or supplier, it says that too.
What is a remap?
A remap is a change to the calibration data stored in a vehicle's engine control unit (ECU), such as the fuel, boost and ignition maps, so that the engine delivers power differently. The changed data is saved as a tuning file and written back to the ECU with a tuning tool. Chiptuning is the older name for the same job.
The basics: what is a remap, an ECU and a map?
ECU
The engine control unit, the computer that manages fuel injection, ignition timing, boost pressure and much more. It holds software, the program, and calibration, the data the program reads while the engine runs. A remap changes the calibration, not the hardware.
TCU
The transmission control unit, the gearbox equivalent of the ECU. Many automatic gearboxes have one, and file services write TCU files as well as ECU files.
Map (calibration map)
A table of values the ECU looks up while the engine runs, for example a boost target for each combination of engine speed and load. The row and column headings are the axes. A tuning file differs from the original read in the values of these maps.
Stage 1, Stage 2 and Stage 3
Stage describes the hardware a file is written for. On TheTuningGroup, Stage 1 is for standard hardware. Stage 2 is for common bolt-ons such as a downpipe, intake and intercooler. Stage 3 is for big builds on an upgraded turbo and internals, with a custom calibration worked out together with you. Other suppliers may draw the lines differently, so always ask which hardware a stage assumes.
Dyno (rolling road)
A dynamometer measures power and torque. Tuners use it to check the result of a file, and bigger builds are worth validating on one.
What tuners and customers actually search for
Customers search for the end result, not the trade vocabulary. UK searches for "ecu remap" ran between 573 and 849 a month through most of 2024 and 2025, with December 2024 dipping to 493, and between 410 and 492 a month since May 2026. The customer-side question, "what is a remap", draws around 70 searches a month.
The words in this glossary barely register. Ahrefs puts "slave tool" and "checksum correction" at zero monthly searches in the UK, and "tuning file", "remap file" and "dtc delete" at 10 to 20. These are words tuners learn from each other and from suppliers, not from Google, which is why they are worth writing down in one place.
UK search interest for "ecu remap"
Show the numbersHide the numbers
| Item | Monthly searches |
|---|---|
| Oct 2023 | 695 |
| Nov 2023 | 679 |
| Dec 2023 | 567 |
| Jan 2024 | 849 |
| Feb 2024 | 711 |
| Mar 2024 | 699 |
| Apr 2024 | 715 |
| May 2024 | 820 |
| Jun 2024 | 655 |
| Jul 2024 | 705 |
| Aug 2024 | 704 |
| Sep 2024 | 597 |
| Oct 2024 | 704 |
| Nov 2024 | 598 |
| Dec 2024 | 493 |
| Jan 2025 | 709 |
| Feb 2025 | 688 |
| Mar 2025 | 657 |
| Apr 2025 | 644 |
| May 2025 | 689 |
| Jun 2025 | 648 |
| Jul 2025 | 672 |
| Aug 2025 | 707 |
| Sep 2025 | 730 |
| Oct 2025 | 657 |
| Nov 2025 | 573 |
| Dec 2025 | 578 |
| Jan 2026 | 581 |
| Feb 2026 | 548 |
| Mar 2026 | 631 |
| Apr 2026 | 554 |
| May 2026 | 446 |
| Jun 2026 | 432 |
| Jul 2026 | 421 |
| Aug 2026 | 410 |
| Sep 2026 | 446 |
| Oct 2026 | 492 |
Files: original read, tuning file and virtual read
Original read (ori, stock file)
The unmodified file read out of the ECU before any change. Every tune starts from it, so send the read itself, never a file that has already been flashed. Ori is trade shorthand for original. On TheTuningGroup you upload it with your order.
Tuning file (mod file, remap file)
The modified version of the original read, with calibration values changed for the vehicle, the stage and the options you ordered. It is what you flash back to the ECU. A tuning file is only as good as the original read it was built from.
Virtual read
An original file taken from a database of files rather than read from the car in front of you. It is convenient, but risky: cars that look identical can carry different software versions, so a file that matches on paper may not match the ECU. See virtual reads and original file databases for the rules worth setting.
File identification
Matching a read to the exact ECU, hardware and software version, so the right approach is used. Portals do it on upload. On TheTuningGroup we identify the ECU and check the read on intake. How a portal recognises your original read covers it in more depth.
Hardware and software numbers (HW and SW)
Identifiers for an ECU's hardware and the software it runs. Two ECUs from the same family with different software numbers can need different files, which is why identification matters.
On a normal job the terms arrive in this order:
- Original read: the untouched file from the ECU.
- Identification: ECU, hardware and software matched.
- Tuning file: built as a slave or master file for the car.
- Checksum correction: so the ECU accepts the edited file.
- Flash: the file is written back to the ECU.
What is a slave tool?
A tuning tool for reading and writing ECUs that, in most setups, is linked to a supplier. The files you flash come from that supplier and are encrypted for your tool, so you flash them but do not edit them. A master tool is the opposite: its owner can open and edit files.
Master vs slave in depthSlave file vs master file
The same custom work from the tuner, in two formats.
| Slave file | Master file | |
|---|---|---|
| Who edits the file | The tuner at your supplier | You can open and adjust it too |
| What you receive | A file encrypted for your tool | An editable file |
| Cost per credit on TheTuningGroup | Lower | Higher |
| Skill you need | Reading, writing and fitting | Map-level knowledge and editing software |
| A change after delivery | A revision request to the supplier | A revision request, or your own edit |
Reading and writing: tools, OBD, bench, boot mode and flashing
Tuning tool
The device that reads an ECU and writes a file back, either through the vehicle's diagnostic port or directly on the ECU board. TheTuningGroup accepts reads from all the major tools, including Alientech, Autotuner, CMD, Dimsport and Magic Motorsport.
OBD read
Reading the ECU through the OBD diagnostic socket, with the ECU left in the car. It is the quickest method and needs no dismantling, but not every ECU allows it.
Bench read
Reading an ECU that has been removed from the car and connected to the tool on a bench with a harness. It is used when OBD access is not supported or is protected.
Boot mode
Reading by putting the ECU's processor into a special mode through contacts on the board, which bypasses the normal software. It is usually done on the bench. Bench vs OBD vs boot mode helps you choose between the three.
Flash (write)
Writing the finished file back into the ECU. Keep the vehicle on a stable power supply while it writes, because an interrupted write can leave an ECU unresponsive.
What is checksum correction?
A checksum is a value calculated from the data in a file, so the ECU can tell whether the file has been changed. Edit a map and the old checksum no longer matches, so the file must be corrected before the ECU accepts it. Files from TheTuningGroup come back checksum-corrected and ready to flash.
Who fixes the checksum on a delegated jobFault codes and options: DTC, DPF off and pops and bangs
DTC (diagnostic trouble code)
A code the ECU stores when it detects a fault, for example P0299, a turbo underboost code. A warning light usually comes with it.
DTC off (DTC removal)
An edit that tells the ECU to stop logging or reacting to a specific code. It is ordered per code. Used well, it stops a warning from a part you have deliberately changed. Used badly, it hides a real fault. When to switch a fault code off, and when not to sets out the line.
DPF off, EGR off and AdBlue or SCR off
Diesel options that take the particulate filter, exhaust gas recirculation or AdBlue dosing logic out of the calibration. TheTuningGroup lists them and sets eligibility per engine. Removing emissions equipment from a road vehicle is illegal or restricted in many countries, so read whether DPF delete is legal in the EU before you offer it.
Pops and bangs
A calibration that adds fuel or retards ignition on the overrun, so unburnt fuel ignites in the exhaust and crackles. It adds heat and stress to the exhaust, which is why the risk and liability is worth thinking through first.
Vmax off
Raising or removing the factory top-speed limiter. Check the speed rating of the tyres first.
Editing tools and business terms: WinOLS, revision, credit and dealer
WinOLS (map editor)
Software for opening an ECU file, finding the maps in it and editing them. A master file is the kind of file you would open in an editor. ECM Titanium is another editor, compared in ECM Titanium vs WinOLS.
Revision
A request to the tuner to adjust a delivered file. On TheTuningGroup you request it on the same order, so the history stays in one place.
Credit
The unit of buying on TheTuningGroup: one credit buys one file. You can buy credits in bulk for a lower per-file price, or pay per file with no bundle. The pricing page shows the live numbers, and credits vs pay per file explains how to choose.
File service
A company that writes tuning files for tuners, who read the car and flash the result. What is a tuning file service walks through the whole route.
Dealer
In the file service trade, a garage, tuner or reseller that orders files on behalf of its own customers. On TheTuningGroup a dealer account covers your whole team, with roles. See for dealers.
Credit and revision are two of the terms you meet on an order. The steps below show where.
Common questions
Do I need to know all of these terms before I order a tuning file?
No. For a first order, four terms cover most of it: original read, tuning file, slave or master, and checksum correction. The order form shows the price live as you choose, so you see what you are buying before you commit.
How it worksIs a tuning file the same as a remap?
Nearly. The remap is the change to the calibration. The tuning file is the saved result of that change, the thing you actually flash into the ECU.
What is the difference between a slave file and a master file?
A slave file is encrypted for your tool and flashed as delivered. A master file is editable and costs more per credit. On TheTuningGroup you choose per order, and both are written for your specific vehicle by a tuner.
Master vs slave in depthDo all tool vendors use these words in the same way?
Not always. How a master or slave relationship is set up differs by tool vendor and licence, so ask the vendor or your supplier if a term matters for a purchase.
Put the terms to work
Create a free account, upload an original read and see the live quote before you commit. No card needed to look around.